ASTM A572/A572M-21 · 高强低合金铌钒结构钢 HLSA Cb-V Steel
A572高强低合金铌钒结构钢A572 HSLA Cb-V Structural Steel
钢材堆场与仓储发货区 Steel plate stockyard
ASTM A572/A572M-21 · HSLA Cb-V Structural Steel

ASTM A572 高强低合金结构钢

High-Strength Low-Alloy Columbium-Vanadium Structural Steel

标准版本 A572/A572M-21五大牌号 Gr42–Gr65中英文对照 Bilingual
首页 Home/ASTM A572 高强低合金结构钢

ASTM A572/A572M 是美标体系中应用广泛的高强低合金(HSLA)铌钒结构钢标准,以 Grade 42 [290]、50 [345]、55 [380]、60 [415]、65 [450] 五个屈服强度级别,覆盖中厚板、型钢、钢板桩与棒材四类产品,用于栓接、焊接与铆接的桥梁和建筑结构。本门户以 2021 版标准为基准,系统整理牌号成分、力学性能、厚度极限、应用对象与中国境内生产使用企业分布。

ASTM A572/A572M covers five grades of high-strength low-alloy (HSLA) columbium-vanadium structural steel — Grades 42 [290], 50 [345], 55 [380], 60 [415] and 65 [450] — in the product forms of plates, shapes, sheet piling and bars, for bolted, welded and riveted bridges and buildings. This portal summarises chemistry, mechanical properties, thickness limits, applications and the supply chain in China, based on the 2021 edition.

5标准牌号 Grades 42–65
290–450 MPa最小屈服强度 Yield point
415–550 MPa最小抗拉强度 Tensile strength
150 mm最大板厚(Gr42)Max plate
01

四个入口

Four entry points

标准体系

Standards

A572/A572M-21 的适用范围、产品形式、引用文件 A6/A6M、A36、A514、A588 与版本演进。

牌号与成分

Grades & chemistry

五个牌号的 C、Mn、P、S、Si 限值,合金类型 1/2/3/5,以及各牌号允许的最大厚度。

应用与选型

Applications

桥梁、建筑钢结构、工程机械、港口起重、电力支架与矿山设备的典型构件与选型逻辑。

供货与质量

Supply & quality

中厚板 6–150 mm、型钢、钢板桩与棒材的订货要素、交货状态、探伤与质保书。

02

A572 的技术定位

Why A572

A572 的核心思路是“微合金化 + 控轧”而非“靠碳当量堆强度”。标准要求在铌(Cb/Nb)、钒(V)、钛(Ti)、氮(N)中按类型 1、2、3 或 5 加入一种或多种,通过晶粒细化与碳氮化物析出获得 290–450 MPa 的屈服强度,同时把碳控制在不高于 0.21%–0.26%、磷硫不高于 0.030%,为焊接与低温韧性留出余量。

与 A36(250 MPa 级)相比,A572 Gr50 的屈服强度提高约 38%,在同等承载力下可减薄截面、降低自重与用钢量;与调质高强钢(如 A514)相比,A572 通常以热轧、控轧或正火状态交货,不依赖淬火回火,工艺链更短,适合大批量中厚板与型钢供应。

A572 achieves its strength through micro-alloying (Cb/Nb, V, Ti, N) and controlled rolling rather than high carbon: grain refinement plus carbonitride precipitation delivers 290–450 MPa yield point while keeping carbon at 0.21–0.26% max and P/S at 0.030% max for weldability and toughness.

标准原文 Scope 1.1

“This specification covers five grades of high-strength low-alloy structural steel shapes, plates, sheet piling, and bars. Grades 42 [290], 50 [345], and 55 [380] are intended for riveted, bolted, or welded structures. Grades 60 [415] and 65 [450] are intended for riveted or bolted construction of bridges, or for riveted, bolted, or welded construction in other applications.”

— ASTM A572/A572M-21, Section 1.1

03

五大牌号速览

Grade overview
左右滑动查看完整表格 · Swipe horizontally for the full table
牌号 GradeRp0.2 / Rm (MPa)伸长率 Elongation最大板厚 Max plate定位 Positioning
A572 Gr42 [290]290 / 41524% (2 in.)150 mm一般建筑与轻型结构 General building & light structures
A572 Gr50 [345]345 / 45021% (2 in.)100 mm应用广泛的通用牌号 Widely used general grade
A572 Gr55 [380]380 / 48520% (2 in.)64 mm中等厚度重载结构 Medium-thickness heavy-duty structures
A572 Gr60 [415]415 / 52018% (2 in.)64 mm栓接/铆接桥梁与重型结构 Bolted/riveted bridges & heavy structures
A572 Gr65 [450]450 / 55017% (2 in.)50 mm高承载、受厚度限制的高强牌号 High-load grade with strict thickness limits

数据依据 ASTM A572/A572M-21 表 1 与表 4;伸长率为 2 in. [50 mm] 标距最小值。Data per Tables 1 and 4 of A572/A572M-21.

04

典型应用场景

Typical applications
切割、钻孔后的钢结构零件
桥梁与建筑节点的切割钻孔件 Cut and drilled structural components
厂内钢板堆场
中厚板现货堆场 Plate stockyard
仓库装车发运
成批中厚板装车发运 Batch loading for delivery

从材料到构件:A572 中厚板经下料、切割、钻孔、组立、焊接、矫正与涂装,进入桥梁、建筑与装备制造现场。

05

使用本门户的方式

How to use this portal

设计端可先从牌号体系确认强度级别与厚度上限,再到力学性能核对伸长率、厚度折减与冲击韧性条款;采购端可直接查看供货产品的规格与交货状态,并按质量合规准备质保书与单证要求;需要跨标准比对时使用选型对照。

Designers start from grades and properties; buyers go to product forms and quality documents; cross-standard substitution is covered in the comparison section.

版本提示 Version note:本门户数据以 ASTM A572/A572M-21ε1(2021 年 5 月批准,2021 年 6 月编辑修正)为准,取代 A572/A572M-18。实际订货应以合同指定的标准版本、补充要求(S5、S18、S30、S32、S81、S99)与双方技术协议为最终依据。Data follows A572/A572M-21ε1; the contractually specified edition and supplementary requirements prevail.

需要 A572 报价或技术资料?

提供牌号、厚度、宽度、长度、数量与交货状态,即可获得规格确认与报价。
Need a quotation or technical documents? Send grade, thickness, width, length and quantity.

联系询价 Contact