ASTM A572/A572M 由 ASTM 委员会 A01(钢、不锈钢及相关合金)下属 A01.02 分委员会维护,现行版本为 2021 年 5 月 15 日批准的 A572/A572M-21,2021 年 6 月作编辑修正(ε1)。标准共 4 页正文,配套表 1–4 与补充要求 S5、S18、S30、S32、S81、S99。
Maintained by ASTM Committee A01 / Subcommittee A01.02, the current edition is A572/A572M-21, approved 15 May 2021 with an editorial correction (ε1) in June 2021.
范围要点逐条解读
Scope, clause by clause| 条款 Clause | 中文要点 Key point (ZH) | English |
|---|---|---|
| 1.1 | 覆盖五个牌号的型钢、钢板、钢板桩与棒材;42/50/55 用于铆接、栓接或焊接结构;60/65 用于桥梁的铆接或栓接,或其他应用的铆接、栓接、焊接结构 | Five grades of shapes, plates, sheet piling and bars; 42/50/55 for riveted, bolted or welded structures; 60/65 for riveted or bolted bridges or other applications |
| 1.2 | 焊接桥梁等对缺口韧性有要求的场合,韧性指标由供需双方协商 | Notch toughness to be negotiated between purchaser and producer |
| 1.3 | A588/A588M 不得在未协商的情况下替代 A572/A572M | A588/A588M shall not be substituted without agreement |
| 1.4 | 必须使用铌、钒、钛、氮中的一种或组合;类型 1、2、3、5 由生产厂选择,除非买方指定(S90) | Cb/Nb, V, Ti, N or combinations required; type at producer's option unless S90 specified |
| 1.5 | 各牌号与产品形式的最大厚度或尺寸见表 1 | Maximum thicknesses per Table 1 |
| 1.6 | 焊接时应采用适合该牌号与使用条件的焊接工艺,可参考 A6/A6M 附录 X3 | Suitable welding procedure; see Appendix X3 of A6/A6M |
| 1.7 | 英制与 SI 单位各自独立作为标准,不得混用或互相换算 | Inch-pound and SI units are separate standards |
| 1.8 | 注释与脚注为说明性内容,不构成强制要求 | Notes and footnotes are explanatory, non-mandatory |
| 1.9 | 由卷板生产且不经热处理(或仅去应力)的结构产品,附加要求按 A6/A6M | Coil-produced products: additional A6/A6M requirements apply |
| 1.10 | 按 WTO/TBT 委员会原则制定的国际标准 | Developed per WTO TBT principles |
依据 ASTM A572/A572M-21 第 1 章整理。Compiled from Section 1 of A572/A572M-21.
版本演进
Edition history| 版本 Edition | 状态 Status | 说明 Notes |
|---|---|---|
| A572-66(1966 年) | 首次发布 Initial adoption | 建立高强低合金铌钒结构钢体系 |
| A572/A572M-07 | 已被替代 Superseded | 采用双单位(ksi / MPa)并行表述 |
| A572/A572M-12 / -12a | 已被替代 Superseded | 细化牌号厚度与化学成分对应关系 |
| A572/A572M-13a | 已被替代 Superseded | 编辑性修订 |
| A572/A572M-18 | 上一版 Previous edition | 取消合金类型 4,保留 1、2、3、5 |
| A572/A572M-21ε1 | 现行 Current | 2021 年 5 月批准,6 月编辑修正;补充 S32、S99 |
版本年份依据 ASTM 标准编号规则:编号后的年份为最近一次修订年份,括号内年份为重批准年份。Edition years follow ASTM designation rules.
引用文件
Referenced documentsASTM A6/A6M
General requirements轧制结构钢棒材、钢板、型钢与钢板桩的通用技术要求:尺寸公差、取样、试验方法、复验与标记。
ASTM A36/A36M
Carbon structural steel250 MPa 级碳素结构钢,是 A572 强度梯度体系的基准参照。
ASTM A514/A514M
Quenched & tempered690 MPa 级调质高强钢,与 A572 构成 250–690 MPa 的强度序列。
ASTM A588/A588M
Weathering steel耐大气腐蚀高强钢,未经协商不得替代 A572。
产品形式
Product forms| 形式 Form | 说明 Description | 典型规格 Typical size |
|---|---|---|
| 钢板 Plates | 中厚板,最大厚度按牌号与表 1 确定 | 6–150 mm(Gr42);6–100 mm(Gr50) |
| 型钢 Shapes | H 型钢、工字钢、角钢、槽钢等结构型钢,按 A6/A6M 分组 | 翼缘或肢厚 ≤75 mm 适用基础成分列 |
| 钢板桩 Sheet piling | U 型、Z 型、直腹板与拱腹板(PS/PSA)断面,S99 可约定锁口强度 | 按断面型号供货 |
| 棒材 Bars | 圆钢、方钢、扁钢;Gr50 圆棒直径可至 275 mm,Gr60 可至 90 mm | 直径 ≤275 mm(Gr50) |
产品形式与尺寸上限依据 A572/A572M-21 表 1。Per Table 1 of A572/A572M-21.
需要 A572 报价或技术资料?
提供牌号、厚度、宽度、长度、数量与交货状态,即可获得规格确认与报价。
Need a quotation or technical documents? Send grade, thickness, width, length and quantity.