A709 的十二个牌号不是十二种“强度档位”,而是五套材料体系的组合:碳素钢、常规高强低合金钢、耐候钢、淬火自回火型钢与不锈钢板。同样是 345 MPa 级,50、50S、50W、HPS 50W、QST 50、50CR 的成分与工艺路线完全不同,可焊性与耐蚀性也不同。
The twelve grades are not twelve strength steps but five material families: carbon steel, conventional HSLA, weathering steel, quenched-and-self-tempered shapes and stainless plate. Six different 345 MPa grades differ in chemistry, processing and weldability.
牌号命名
Designation普通牌号写作 Grade + 英制屈服强度,方括号内为公制值,如 Grade 50 [345]。带 W 的牌号为耐候钢(Weathering),带 S 的为受拉专用(Tension),带 CR 的为耐腐蚀不锈钢(Corrosion Resistant),QST 表示淬火自回火工艺(Quenching and Self-Tempering),HPS 表示高性能钢(High Performance Steel)。
同一牌号下还分 A/B 成分类型或不同厚度区间,订货时应写明。例如 Grade 50W 分 Type A 与 Type B,分别对应 A588 的 A、B 两个成分;HPS 100W 在厚度超过 65 mm 时屈服强度降至 620 MPa,力学指标随厚度变化。
十二牌号总表
Grade summary| 牌号 | 屈服 MPa | 抗拉 MPa | 伸长率 8 in. / 2 in. | 厚度上限 | 焊接要点 |
|---|---|---|---|---|---|
| 36 [250] | 250 | 400–550 | 20 / 23 | ≤100 mm(板) | 可焊,常规工艺 |
| 50 [345] | 345 | 450 min | 18 / 21 | ≤100 mm(板) | 可焊,按 WPS 评定 |
| 50S [345S] | 345 | 450 min | 18 / 21 | ≤100 mm(板) | CE ≤0.45%(厚翼缘 0.47%) |
| QST 50 [QST 345] | 345 | 450 min | 18 / 21 | 型钢 only | CE ≤0.38% |
| QST 50S [QST 345S] | 345 | 450 min | 18 / 21 | 型钢 only | CE ≤0.38% |
| 50W [345W] | 345 | 485 min | 18 / 21 | ≤100 mm(板) | A/B 两种成分,FHWA 已验证 |
| HPS 50W [HPS 345W] | 345 | 485 min | 18 / 21 | ≤100 mm(板) | 低碳当量,低温韧性好 |
| 50CR [345CR] | 345 | 485 min | 18 / 21 | ≤50 mm(板) | 需专用焊材与工艺评定 |
| QST 65 [QST 450] | 450 | 550 min | 15 / 17 | 型钢 only | CE ≤0.43% |
| QST 70 [QST 485] | 485 | 620 min | 14 / 16 | 型钢 only | CE ≤0.45% |
| HPS 70W [HPS 485W] | 485 | 585–760 | 19 | ≤100 mm(板) | 低碳当量,TMCP 或调质 |
| HPS 100W [HPS 690W] | 690 | 760–895 | 18 | ≤65 mm(板) | 需专项工艺评定与预热 |
伸长率以 200 mm(8 in.)与 50 mm(2 in.)双标距给出;板宽超过 600 mm 时伸长率下调 2 个百分点。Elongation per Table 1; reduced by 2 points for plates wider than 600 mm.
普通与耐候牌号成分
Carbon, HSLA and weathering grades| 牌号 Grade | C max | Mn | P max | S max | Si | Cu | 其他 Other |
|---|---|---|---|---|---|---|---|
| 36 [250] | 0.25–0.28 | 0.60–1.20 | 0.030(0.04) | 0.030(0.05) | 0.15–0.40 | 0.20 min | 按厚度分档,见表 2 |
| 50 [345] | 0.23 | ≤1.35(下限 0.80 / 0.50) | 0.030(0.04) | 0.030(0.05) | 0.40 | 0.20 min | Nb 0.005–0.05;V 0.01–0.15 |
| 50S [345S] | 0.23 | 0.50–1.60 | 0.035 | 0.045 | 0.40 | 0.60 | V ≤0.15;Nb ≤0.05;CE ≤0.45 / 0.47 |
| 50W Type A | 0.19 | 0.80–1.25 | 0.030(0.04) | 0.030(0.05) | 0.30–0.65 | 0.25–0.40 | Ni ≤0.40;Cr 0.40–0.65;V 0.02–0.10 |
| 50W Type B | 0.20 | 0.75–1.35 | 0.030(0.04) | 0.030(0.05) | 0.15–0.50 | 0.20–0.40 | Ni ≤0.50;Cr 0.40–0.70;V 0.01–0.10 |
括号内为型钢、棒材、宽度 ≤380 mm 钢板允许的放宽值。Values in brackets apply to shapes, bars and plates up to 380 mm wide.
HPS 高性能钢成分
HPS grades| 元素 Element | HPS 50W / HPS 70W | HPS 100W |
|---|---|---|
| C max | 0.11 | 0.08 |
| Mn | 1.10–1.35(>65 mm 至 1.50) | 0.95–1.50 |
| P max | 0.020 | 0.015 |
| S max | 0.006(钙处理) | 0.006 |
| Si | 0.30–0.50 | 0.15–0.35 |
| Cu | 0.25–0.40 | 0.90–1.20 |
| Ni | 0.25–0.40 | 0.65–0.90 |
| Cr | 0.45–0.70 | 0.40–0.65 |
| Mo | 0.02–0.08 | 0.40–0.65 |
| V | 0.04–0.08 | 0.04–0.08 |
| Nb | — | 0.01–0.03 |
| Al | 0.010–0.040 | 0.020–0.050 |
| N max | 0.015 | 0.015 |
HPS 系列以低碳当量换取焊接性,S 含量压到 0.006% 以内。Low carbon equivalent with S held at 0.006 % max.
QST 型钢成分
QST shapes| 元素 Element | QST 50 / QST 50S | QST 65 | QST 70 |
|---|---|---|---|
| C max | 0.12 | 0.12 | 0.12 |
| Mn max | 1.60 | 1.60 | 1.60 |
| P / S max | 0.030 | 0.030 | 0.030 |
| Si max | 0.40 | 0.40 | 0.40 |
| Cu max | 0.45 | 0.35 | 0.45 |
| Ni max | 0.25 | 0.25 | 0.25 |
| Cr max | 0.25 | 0.25 | 0.25 |
| Mo max | 0.07 | 0.07 | 0.07 |
| Nb max | 0.05 | 0.05 | 0.05 |
| V max | 0.06 | 0.08 | 0.09 |
| CE max | 0.38 | 0.43 | 0.45 |
QST 型钢禁止故意加硼;自回火温度须在质保书中报告。Boron shall not be intentionally added; STT shall be reported.
50CR 不锈钢板成分
Grade 50CR| 元素 | C | Mn | P | S | Si | Ni | Cr | N |
|---|---|---|---|---|---|---|---|---|
| 上限或范围 % | 0.030 | 1.50 | 0.040 | 0.010 | 1.00 | 1.50 | 10.5–12.5 | 0.030 |
50CR 以 12% Cr 马氏体不锈钢体系提供耐蚀性,交货状态为正火回火或调质。12 % Cr martensitic stainless, normalized and tempered or quenched and tempered.
需要 A709 报价或技术资料?
提供牌号、T/F 标识、冲击分区、厚度、宽度、长度、数量与交货状态,即可获得规格确认与报价。
Need a quotation or technical documents? Send grade with T/F suffix, impact zone, thickness, width, length and quantity.